Mainboard AK37GT, AK37GTR

Note: AK37GT is the version without RAID controller.

• Chipset
  VIA Apollo KT400 Chipset
  Northbridge: VIA VT8367
  Southbridge: VIA VT8235
• Socket A CPU Support
  supports the following 462pin socket A processors: 
  AMD Athlon XP and Duron processors for socket A with 200/266/333MHz FSB
  supports Thunderbird, Palomino (model 6), T-Bred (model 8) and Barton up to 3000+
  Note: If an Athlon XP processor with 166/333MHz FSB is used, for KT400-chipset the DDR333-memory is essential, as only synchronous operation is possible on this setting.
  Burn Proof CPU protection only for AthlonXP
  (CPU Burning Proof)
  Adjustable in BIOS:
  System clock frequency (FSB) infinitely from 100 to 200MHz adjustable
  CPU-multiplicator from 5x to 14 x
  CPU-voltage Vcore fine adjustment from 1,100...1,825 and more up to 2,400V
  DDR-voltage: 2,55...2,85V
  AGP-voltage: 1,6...1,8V
  Chipset-voltage: 2,6...2,8V
• Expansion Slots:
  1 x AGP (supports AGP 8X and 4X mode)
  Important Note: AGP-Slot supports only 1,5V-mode (3,3V is not supported)
  5 x 32 Bit PCI
• Onboard IDE Controller
  2-Channel Enhanced PCI IDE
  up to 4 IDE devices
  support up to UltraDMA/133 (downward compatible)
  with ATA-133-cable
• Only AK37GTR: IDE RAID Controller, UDMA/133
  Chip: High Point 372, support UltraDMA/133
  supports RAID-Modus 0 and 1 (even simultaneously)
  with two IDE-connectors up to 4 hard disks
  Only AK37GTR Serial ATA IDE RAID Controller, ATA150
  Marvell 88i8030 Serial ATA Bridge with support of Highpoint 372 Controller
  also supports RAID-mode 0 and 1
  SerialSelect-setting in BIOS:
  
  For both channels of the RAID-controller the requested connector can be chosen:
  Serial-ATA or IDE-hard disk
• Integrated Ethernet-Function
  Built-in VT8233 Fast Ethernet Controller 10/100MBit/s
• Hardware Monitoring
  CPU-Temperature, system voltage and fan revolution can be monitored
  Burn Proof CPU protection only for AthlonXP
  (CPU Burning Proof)
• More Interfaces
  Back panel:
  1 x PS/2-Mouse
  1 x PS/2-Keyboard
  1 x Parallel (SSP/EPP/ECP)
  2 x Serial (16550 compatible, Fifo)
  2 x USB 2.0 (four more USB 2.0 connectors onboard)
  1 x Line-In
  1 x Line-Out
  1 x Microphone
  1 x MIDI/Joystick-connector
  Onboard:
  1 x Floppy Drive
  1 x Infrared (IrDA-adapter not included in delivery)
  1 x WOL (Wake on Lan)
  4 x USB 2.0 (two more USB 2.0 connectors on the back panel)
  3 x Fans (CPU, AGP-card, case)
  3 x Audio (CD-Audio-in, TAD, AUX)
• Memory
  4 x 184-Pin DIMM-Socket
  up to 4 GB DDR SDRAM memory modules
  supports PC1600/PC2100/PC2700 (DDR200/266/333)
  Adjustment for PC3200 (DDR400) also available.
  for 64, 128, 256, 512 or 1024 MB
  supports 6 banks unbuffered DDR SDRAM up to 3 GB capacity
  or 8 banks registered DDR SDRAM up to 4 GB capacity
  (max. 512Mb x8/x16 DRAM technology)
  No ECC-function
  Note: KT400-chipset requires at 166MHz FSB synchronous memory frequency at 166MHz (DDR333) as well.
  The chipset is designed according to VIA for max. 2x DDR333 and 1x DDR400.
• Integrated Multichannel Audio Function:
  Realtek 650 chipset
  supports 5.1 speakers, audio in 6-channel-mode
  Back Panel Connectors: line-in, line-out, mircophone, MIDI/gameport
  Bracket Connector: for bass/center, bracket optionally included in delivery
  Multichannel: line-out = front, line-in = rear and onboard connector for bass/center
  More line-ins on the mainboard, audio-in for CD-ROM and AUX.
• Power Management
  ACPI v1.0 (Advanced Configuration and Power Interface)
  APM v1.2 (Advanced Power Management)
• supports Suspend to RAM and Suspend to Disk
  Power on after power fail: Auto/Off)
• BIOS
  2 MBit Flash EPROM
  Award BIOS V6.0PG
  supports Green PC, Desktop Management Interface (DMI 2.3)
• Form Factor
  ATX: 30,5 x 24,5 cm
• Delivery Content
  Manual, driver-CD, back panel-bracket, IDE- and floppy-cable, bass/center-adapter, USB-adapter
  Only AK37GTR: RAID-manual, second IDE-cable, Serial-ATA cable
  
• ATX-Power Supply Connector
  Standard 20-Pin-ATX-power supply connector
  With additional 4-pin connector for a better supply of the 12V-bar, a power supply with this connector is not essential for safe operation