![](../images/p_01.jpg) |
![](../images/p_02.jpg) |
![](../images/p_03.jpg) |
(1) Unscrew the three thumbscrews. |
(2) Slide the cover backwards then lift to remove. |
(3) Unplug the Card Reader signal cable. |
|
![](../images/p_04.jpg) |
![](../images/p_05.jpg) |
![](../images/p_06.jpg) |
(4) Unbuckle the rack clips. Lift to remove. |
(5) Remove the fan duct |
(6) Disconnect the fan power cable. Unscrew the ICE heat-pipe module and remove. |
|
![](../images/p_07.jpg) |
![](../images/p_08.jpg) |
![](../images/p_09.jpg) |
(7a) Pentium 4 installation. Unlock and raise the socket lever. Remove the protective cover. |
(8a) Align the CPU according to the above diagram. Close the cover and lock with lever. |
(7b) AMD Athlon 64 installation. Raise the socket lever to 90°. |
|
![](../images/p_10.jpg) |
![](../images/p_11.jpg) |
![](../images/p_12.jpg) |
(8b) Align the CPU according to the above diagram. Gently insert. Return the lever to the horizontal. |
(9) Apply an even layer of thermal paste to the surface of the CPU. |
(10) Install the ICE module. Refasten the screws. Attach the cables (header 1). Replace the fan duct. |
|
![](../images/p_13.jpg) |
![](../images/p_14.jpg) |
![](../images/p_15.jpg) |
(11) Install DDR. Open the DIMM latches. Align the RAM and insert vertically. Close latches. |
(12) Floppy drive installation (optional). Attach the toolless brackets to the FDD as shown. |
(13) Slide the floppy drive into the rack mount. |
|
![](../images/p_16.jpg) |
![](../images/p_17.jpg) |
![](../images/p_18.jpg) |
(14) Alternatively, you can install a hard drive in this position. Place in rack and press firmly to lock. |
(15) Attach the 4 dampers on top of the installed drive and press firmly. |
(16) Optical drive installation. Attach the toolless brackets to the optical drive as shown. |
|
![](../images/p_19.jpg) |
![](../images/p_20.jpg) |
![](../images/p_21.jpg) |
(17) Slide the optical drive into the rack mount. |
(18) Align the drive optical eject button. You may need to swap the "control rod". |
(19) Insert the rack mount into the chassis. Lock in position. Attach card reader cable. |
|
![](../images/p_22.jpg) |
![](../images/p_23.jpg) |
![](../images/p_24.jpg) |
(20) Attach drives signal and power cables. Attach signal cables to the motherboard. |
(21) Install SATA drives. Attach the toolless brackets as shown above |
(22) Insert the hard drive into the chassis. Lock latches to secure. Repeat as appropriate. |
|
![](../images/p_25.jpg) |
![](../images/p_26.jpg) |
![](../images/p_27.jpg) |
(23) Attach the hard drive signal and power cables. |
(24) Install expansion card. Unscrew the back panel expansion slot bracket. |
(25) Install expansion card and secure bracket. |
|
![](../images/p_28.jpg) |
![](../images/p_29.jpg) |
![](../images/p_30.jpg) |
(26) Close the cover and refasten the screws. |
(27) Attach the front feet to the base of the chassis. |
(28) Finished! |