• Fanless and silent
    Completely fanless, no fan noise at all
    Passive cooling through convective heat transfer
    Perfect to be used in noise-sensitive environments
    Fanless means less dust and thus virtually no maintenance required
    Notice: Please make sure the system is always operated in 
    upright position using either its stand or the optional VESA mount. 
    Ventilation holes must not be blocked to ensure sufficient cooling.
  • Low power consumption
    Power consumption: ca. 8.7 W (idle mode) and ca. 16.3 W (full load)
    (Configuration: 4 GB RAM, 120 GB SSD and Windows 8.1)
  • Chassis
    Dimensions without stand: 20 x 16 x 3.6 cm (DxHxW) = 1.15 litres
    Weight: 2.1 kg net, 2.8 kg gross
    Hole for Kensington Lock at the back panel
    Optional accessory: 75mm and 100mm VESA mounting kit (PV03)
  • Operation System
    This system comes without operating system. It is compatible with
    - Windows 10 (64 bit)
    - Windows 8 / 8.1 (64 bit)
    - Windows 7 (64 bit) [2]
    - Linux (64 Bit) [3]
  • Processor
    Intel Celeron J1900, Quad Core
    CPU clock frequency: 2.00 GHz, max. Turbo frequency: 2.42 GHz
    Silvermont architecture, Bay Trail-D platform, 22nm structure
    CPU cores/Threads: 4/4
    Cache: 2 MB
    Thermal Design Power (TDP): 10W
    SOC design with integrated graphics processor
  • Integrated Graphics
    The Graphics Processing Unit (GPU) is integrated into the processor
    Intel HD Graphics (7th gen), graphics frequency: 688~854 MHz
    Supports DirectX 11.0, OpenGL 4.0, OpenCL 1.2, HDCP 1.3 (Blu-ray)
    Execution Units (EU): 4
    Three video outputs:
    - HDMI: max. 1920x1200 resolution @ 60Hz
    - Display Port: max. 2560x1600 resolution @ 60Hz
    - D-Sub (VGA): max. 1920x1200 resolution @ 60Hz
    Dual display: supports max. two independent displays
    Full hardware acceleration:
    - for decode: H.264, MPEG2, MVC, VC-1, VP8, MJPEG 
    - for encode: H.264, MPEG2, MVC
  • UEFI Firmware
    8Mbit Flash ROM with AMI's Aptio UEFI BIOS Firmware
    Based on the Unified Extensible Firmware Interface (UEFI) [1]
    Supports Power fail resume / AC power on state / always on / always off
    Supports Wake-on-LAN (WOL) from S3, S3, S5 ACPI states
    Supports boot up from external flash memory cards
  • Memory
    1x SO-DIMM slot with 204 pins
    Supports one module DDR3L-1333 (PC3-10600) at 1.35V
    Maximum capacity: 8 GB
    DDR3L-1600 is supported at DDR3L-1333 clock rate
    Caution: This mainboard does only support 1.35V DDR3L memory modules.
    Note: DDR3L has a lower operation voltage compared to DDR3
  • Hard disk drive/SSD (2.5")
    Supports one Serial ATA hard disk (5400 / 7200 rpm)
    or one SATA SSD drive in 6.35cm/2.5" format
    Serial ATA II Interface with up to 300 MB/s transfer speed
    Supports a drive with max. 9.5 mm height
    Supports Unified Extensible Firmware Interface (UEFI)
  • Integrated Audio
    Realtek ALC269 Audio Codec with Azalia and D3 mode support
    Two analog audio connectors (3.5mm): 
    1) Line out (head phone)
    2) Microphone input
  • Card Reader
    Integrated card reader supports SD, SDHC and SDXC memory flash cards
  • Wired Network
    RJ45 connector supports Gigabit LAN at 10/100/1000 Mbit/sec.
    Network controller Realtek RTL8411
    Supports Wake-on-LAN (WOL) from S3, S3, S5 ACPI states
    Supports network boot by Preboot eXecution Environment (PXE)
  • Wireless Network (WLAN)
    Half-size Mini PCIe card with RTL8188EE chip
    Supports IEEE 802.11b/g/n, max. 150Mbps up-/downstream
    Security: WPA/WPA2(-PSK), WEP 64/128bit, IEEE 802.11x/i
  • LEDs and Buttons
    Power button
    Power LED (blue)
  • Front Panel Connectors
    2x RS232 serial ports (supports 5V/12V auxiliary voltage,
    the upper port is switchable to RS422 / RS485)
    1x USB 2.0
    SD card reader
  • Back Panel Connectors
    HDMI digital video and audio output
    DisplayPort digital video and audio output
    D-Sub/ VGA analog video output (15 pin)
    1x USB 3.0
    3x USB 2.0
    Gigabit network (LAN, RJ45)
    Audio Line-out (head phone)
    Microphone input
    DC input for the external power adapter
  • Power Supply
    External 40W AC/DC power adapter (fanless), 19V / 2.1A
    AC Input: 100~240V AC, 50~60Hz
    Automatic voltage adjust
    Dimensions: 89.5 x 37 x 26.5 mm (LWH)
    DC Connector: 5.5/2.5mm (outer/inner diameter)
  • Optional Accessories
    VESA mount made of metal (PV03)
  • 24/7 nonstop operation
    This device is approved for 24/7 permanent operation.
    Requirements:
    - Free circulation of air amongst the PC must be guaranteed.
    - Ventilation holes must be clear.
    - If a hard disk is installed, this must also be approved for permanent 
    operation by its manufacturer.
  • Environmental Spec
    Operating temperature range: 0~35°C
    Relative humidity range: 10~90% (non-condensing)
  • Certification and Compliance
    EMI: FCC, CE, BSMI, C-Tick
    Safety: ETL, CB, BSMI
    Other: RoHS, Energy Star, ErP
    This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
    (1) 2004/108/EC relating to electromagnetic compatibility (EMC),
    (2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
    (3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
    (4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)

[1] UEFI-Firmware (versus BIOS)
Just as many modern PCs, the XS36V4 does away completely with a BIOS, but uses a pure *) UEFI firmware instead. The terms UEFI firmware and BIOS are widely used synonymously, but hardware initialising is now performed by the UEFI. Users might not even notice, but the operating system must be installed and executed in UEFI mode. UEFI creates a GUID Partition Table (GPT) on the system partition instead of a Master Boot Record (MBR). A PC running UEFI firmware alone but have a 64-bit operating system installed.
*) Notice: In transition period from BIOS to UEFI mainboard manufacturers still used to employ a traditional BIOS for compatibility reasons. Thanks to the integrated "Compatibility Support Module" (CSM), older Windows versions could boot from mainboards with a UEFI firmware.
[2] Windows 7 64-bit is supported since BIOS version XS36V400.110. If a BIOS update is required, the built-in UEFI shell must be used. Please refer to the FAQ section on the Shuttle website for more information on this matter. Prior to the installation of Windows 7, BIOS must be entered and "Windows 7" must be selected as the operating system under "Boot", "OS-Selection". 
[3] Linux 64-bit: A number of Linux distributions with updated Kernel versions have already been tested successfully (date: June 2014). Please refer to the FAQ section on the Shuttle website for more information on this matter.

© 2020 Shuttle Europe | Legal notice | Contact | Terms and Conditions | Privacy Policy | Sitemap