- Fanless and silent
Completely fanless, virtualy noiseless
Passive cooling through convective heat transfer
Perfect to be used in noise-sensitive environments
Fanless means less dust and thus virtually no maintenance required - Low power consumption
Power consumption: ca. 8.4 W (idle mode) and ca. 19.6 W (full load)
(Configuration: 4 GB RAM, 64 GB SSD and Windows 8.1) - Operation Position
Please make sure the system is always operated in
upright position using either its stand or the optional VESA mount.
Ventilation holes must not be blocked to ensure sufficient cooling. - Chassis
Dimensions without stand: 20 x 16 x 3.6 cm (DxHxW) = 1.15 litres
Hole for Kensington Lock at the back panel
Optional accessory: 75mm and 100mm VESA mounting kit (PV03) - Operation System
This system comes without operating system.
It is compatible with Windows 7 / 8.1 / 10 (64-bit) und Linux (64-bit) [3]
Caution: Windows 8 is not supported - Processor
Intel Celeron N3050, Dual Core
CPU clock frequency: 1.6 GHz, max. Turbo frequency: 2.16 GHz
Braswell platform, Airmont architecture, 14 nm structure
CPU cores / Threads: 2 / 2
Cache: 2 MB
Thermal Design Power (TDP): 6 W
Scenario Design Power (SDP): 4 W
Supports AES-NI and VT-x
SOC design with integrated graphics processor, no chipset required - Integrated Graphics
The Graphics Processing Unit (GPU) is integrated into the processor
Intel HD Graphics (8th Gen), graphics frequency: 320~600 MHz
Supports DirectX 11.2, OpenGL, Quick Sync
Execution Units (EU): 12
Three video outputs:
- HDMI 1.4b: max. 1920 x 1200 resolution @ 60Hz
- Display Port 1.1a: max. 2560 x 1600 resolution @ 60Hz [2]
- D-Sub (VGA): max. 1920 x 1200 resolution @ 60Hz
Triple display: supports max. three independent displays simultaneously - UEFI Firmware
8Mbit Flash ROM with AMI's Aptio UEFI BIOS Firmware
Based on the Unified Extensible Firmware Interface (UEFI) [1]
Supports Power fail resume / AC power on state / always on / always off
Supports Wake-on-LAN (WOL) from S3, S3, S5 ACPI states
Supports boot up from external flash memory cards - Memory
1x SO-DIMM slot with 204 pins
Supports one module DDR3L-1333 (PC3-10600) at 1.35V
Maximum capacity: 8 GB
DDR3L-1600 is supported at DDR3L-1333 clock rate
Caution: This mainboard does only support 1.35V DDR3L memory modules.
DDR3L has a lower operation voltage compared to DDR3 - Hard disk drive/SSD (2.5")
Supports one Serial ATA hard disk (5400 / 7200 rpm)
or one SATA SSD drive in 6.35cm/2.5" format
Serial ATA III Interface with up to 600 MB/s transfer speed
Supports a drive with a max. height 9.5 mm
Supports Unified Extensible Firmware Interface (UEFI) - Integrated Audio
Realtek ALC269 Audio Codec with Azalia and D3 mode support
Two analog audio connectors (3.5mm):
1) Line out (head phone)
2) Microphone input - Card Reader
Integrated card reader
supports standard SD, SDHC and SDXC memory flash cards - Wired Network
RJ45 connector supports Gigabit LAN at 10/100/1000 Mbit/sec.
Intel i211 Ethernet Controller with MAC, PHY and PCIe interface
Supports Wake-on-LAN - Wireless Network (WLAN)
Half-size Mini PCIe WLAN card
Supports IEEE 802.11b/g/n, max. 150Mbps up-/downstream (1T1R) - LEDs and Buttons
Power button
Power LED (blue) - Front Panel Connectors
2x RS232 serial ports (support of an auxiliary voltage of 5//12V,
the upper port is switchable to RS422 / RS485)
1x USB 2.0
SD card reader - Back Panel Connectors
HDMI 1.4b digital video and audio output
DisplayPort 1.1a digital video and audio output
D-Sub/ VGA analog video output (15-pin)
2x USB 3.0
2x USB 2.0
Gigabit network (LAN, RJ45)
Audio Line-out (head phones)
Microphone input
DC input for the external power adapter - Power Supply
External 40W AC/DC power adapter (fanless)
AC Input: 100~240V AC, 50~60 Hz
DC Output: 19V / 2.1 A
Automatic voltage adjust
Dimensions: 89.5 x 37 x 26.5 mm (LWH)
DC Connector: 5.5/2.5mm (outer/inner diameter) - Optional Accessories
VESA mount made of metal (PV03) - 24/7 Nonstop Operation
This device is approved for 24/7 permanent operation.
Requirements:
- Free air circulation around the PC must be guaranteed.
- Ventilation holes must be kept clear.
- Any installed hard disk must also be approved for permanent
operation by its manufacturer (max. one hard disk) - Environmental Spec
Operating temperature range: 0~35°C
Relative humidity range: 10~90% (non-condensing) - Certification and Compliance
EMI: FCC, CE, BSMI, C-Tick
Safety: ETL, CB, BSMI
Other: RoHS, Energy Star, ErP
This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
(1) 2004/108/EC relating to electromagnetic compatibility (EMC),
(2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
(3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
(4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)
[1] UEFI-Firmware (versus BIOS)
Just as with many modern PCs, the XS35V4 does away completely with a BIOS, but uses a pure *) UEFI firmware instead. The terms UEFI firmware and BIOS are widely used synonymously, but hardware initialising is now performed by the UEFI. Users might not even notice, but the operating system must be installed and executed in UEFI mode. UEFI creates a GUID Partition Table (GPT) on the system partition instead of a Master Boot Record (MBR). A PC running pure UEFI firmware alone must have a 64-bit operating system installed.
[2] 4K resolution
Playback of videos in 4K resolution (3840x2160) at 30Hz is technically possible through both HDMI and DisplayPort. However Shuttle does not recommend it, as the refresh rate appears to be too low for cursor moves and the processor performance is considered to be not sufficient for fluent playback of 4K content.
[3] Selection of the Operation Systrem
Prior to the installation of the operation system, please enter BIOS (press "Delete" key while booting), switch to "Boot" menu and then change the setting "OS Select" according to the operation system used.
