- Fanless and silent
Completely fanless, virtualy noiseless
Passive cooling through convective heat transfer
Perfect to be used in noise-sensitive environments
Fanless means less dust and thus virtually no maintenance required - Chassis
Slim 3-litre chassis, colour: black
Dimensions: 238 x 200 x 72 mm (LWH) = 3.4-litre
Open front - without covers for easy access to the front panel connectors - Operation Position
1) Horizontal
2) Vertically with optional stand PS01
3) Vertically with optional VESA mount PV02
(e.g. VESA-mounted behind an appropriate monitor)
In vertical position, the front USB ports should point upwards.
Ventilation holes must not be blocked to ensure sufficient cooling. - Operation System
This system comes without operating system.
It is compatible with
- Windows 10 (64-bit)
- Linux (64-bit) Kernel 4.8 or higher
Note: Windows 7, 8 and 8.1 are not supported - Processor
Intel® Celeron® Processor J3355, Dual Core
CPU clock frequency: 2.0 GHz, max. Turbo frequency: 2.5 GHz
Apollo Lake platform, Goldmont architecture, 14 nm structure
CPU cores / Threads: 2 / 2
L2 Cache: 2 MB
Thermal Design Power (TDP): 10 W
Supports AES-NI, VT-x (EPT), VT-d, Secure Boot
SOC design with integrated graphics processor, no chipset required - Integrated Graphics
The Graphics Processing Unit (GPU) is integrated in the processor
Intel® HD Graphics 500 (9th Gen), graphics frequency: 250~700 MHz
Supports DirectX 12, OpenGL 4.3, OpenCL 1.2, OpenGL ES 3.0, Intel Quick Sync Video, Intel Clear Video (HD)
Execution Units (EU): 12
Video outputs (Resolution):
- HDMI 1.4b: max. 1920 x 1200 @ 60 Hz oder 3840 x 2160 @ 30 Hz
- D-Sub (VGA): max. 1920 x 1200 resolution @ 60 Hz
Supports two displays simultaneously via HDMI and VGA port. - UEFI Firmware
16 MB Flash ROM with AMI's Aptio UEFI BIOS Firmware
Based on the Unified Extensible Firmware Interface (UEFI) [1]
Supports Power fail resume / AC power on state / always on / always off
Supports Wake-on-LAN (WOL) from S3, S4, S5 ACPI states
Supports boot up from external flash memory cards
Supports embedded Firmware TPM v2.0 (fTPM) - Memory
2x 204-pin SO-DIMM slot
Supports DDR3L-1600/1866 (PC3-12800/14900) SDRAM at 1.35V
Supports Dual Channel mode
Supports max. 8 GB per DIMM
Maximum total size: 8 GB (either 1x 8 GB or 2x 4 GB)
Supports two unbuffered DIMM modules (no ECC)
Note: This mainboard does only support 1.35 V DDR3L memory modules.
DDR3L has a lower operation voltage as compared to DDR3 - Bays for Hard disk drive/SSD
Combined 2.5"/3.5" bay supports one SATA storage drive
- 3.5" SATA hard disk drive or
- 2.5" SATA hard disk drive or
- 2.5" SATA SSD drive
Serial ATA III Interface with up to 600 MB/s transfer speed
One pre-installed SATA cable (data / power)
Supports Unified Extensible Firmware Interface (UEFI) - M.2 expansion slot for SSD card
M.2 2280 slot
Interfaces: PCI-Express Gen. 2.0 X4 (max. 16 Gbit/s) and SATA v3.0 (max. 6 Gbit/s)
Supports M.2 cards with a width of 22 mm
and a length of 42, 60 or 80 mm (type 2242, 2260, 2280)
Supports SATA SSDs (BM-Key) or PCIe SSDs (M-Key) - Integrated Audio
Realtek ALC662 Audio Codec
Two analog audio connectors (3.5 mm):
1) Line out (headphones)
2) Microphone input - Wired Network
RJ45 connector supports Gigabit LAN at 10/100/1000 Mbit/s.
Intel i211 Ethernet Controller with MAC, PHY and PCIe interface
Supports Wake-on-LAN - Optional WLAN
M.2-2230 slot for optional WLAN kit "WLN-M" - LEDs and Buttons
Power button
Power LED (blue)
HDD LED (yellow) - Front Panel Connectors
Microphone input
Audio Line-out (head phones)
2x USB 3.0
2x USB 2.0
3x RS232 COM ports - Back Panel Connectors
HDMI 1.4b digital video and audio output
D-Sub/ VGA analog video output (15-pin)
2x USB 2.0
Gigabit network (LAN, RJ45)
5x RS232 serial port, 9-pin D-Sub (support of an auxiliary voltage of 5 / 12 V
and one port is switchable to RS422 / RS485)
DC input for external power adapter
2x perforation for external WLAN antennas - Power-on Jumper
Jumper JP5 for power on after power fail (hardware solution) [2] - Power Supply
External 65 W AC/DC power adapter (fanless)
AC Input: 100 ~ 240 V AC, 50 ~ 60 Hz
Automatic voltage adjust
DC Output: 19 V / 3.42 A
DC Connector: 5.5 / 2.5 mm (outer/inner diameter)
Remark: the DC-input of the computer supports an external power source
with either 12 V ± 5 % (65 W) or 19 V ± 5 % (65 W). - Supplied Accessories
Quick Installation Guide
Driver DVD (Windows 64-bit)
External 19V / 65 W power adapter with power cord
Pre-installed cables for a SATA drive, screws for installation - Optional Accessies:
- Vertical stand (PS01)
- VESA mount (PV02)
- WLAN kit with two external antennas (WLN-M) - 24/7 Nonstop Operation
This device is approved for 24/7 permanent operation.
Requirements:
- Free air circulation around the PC must be guaranteed.
- Ventilation holes must be kept clear.
- Any installed disk must also be approved for permanent
operation by its manufacturer - Environmental Spec
Operating temperature range: 0 ~ 40 °C
Relative humidity range: 10 ~ 90 % (non-condensing) - Certification and Compliance
EMI: FCC, CE, BSMI, RCM, VCCI, R&TTE
Safety: CB, BSMI, ETL, CCC
Other: RoHS, Energy Star, ErP
This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
(1) 2004/108/EC relating to electromagnetic compatibility (EMC),
(2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD) and
(3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP)
[1] UEFI-Firmware (versus BIOS)
Just as with many modern PCs, the Shuttle XPC slim Barebone XC60J does away completely with a BIOS, but uses a pure UEFI firmware instead. The terms UEFI firmware and BIOS are widely used synonymously, but hardware initialising is now performed by the UEFI. Users might not even notice, but the operating system must be installed and executed in UEFI mode. UEFI creates a GUID Partition Table (GPT) on the system partition instead of a Master Boot Record (MBR). A PC running pure UEFI firmware alone must have a 64-bit operating system installed.
[2] Power-On after Power-Fail
The BIOS setup provides a "Power-On after Power Fail" function that can be found under "Power Management Configuration". As the name indicates, this function determines the PC's behaviour after power failure: (1) unconditional power on, (2) restore former status or (3) keep system turned off. As a matter of the nature of this function, it may fail after short power failures. This is why the Shuttle XPC slim Barebone XC60J also comes with a hardware-based solution. By removing Jumper JP5, the system will start unconditionally once power is supplied.
