- Fanless and silent
Completely fanless, no fan noise at all
Passive cooling through convective heat transfer
Perfect to be used in noise-sensitive environments
Fanless means less dust and thus virtually no maintenance required
Notice: Please make sure the system is always operated in
upright position using either its stand or the optional VESA mount.
Ventilation holes must not be blocked to ensure sufficient cooling. - Low power consumption
Power consumption: ca. 7.5 W (idle mode) and ca. 15.4 W (full load)
(Configuration: 4 GB RAM, 120 GB SSD and Windows 8.1) - Chassis
Dimensions without stand: 25.2 x 16.2 x 3.85 cm (DxHxW) = 1.57 L
Weight: 2.1 kg net, 2.8 kg gross
Hole for Kensington Lock at the back panel
Optional accessory: 75mm and 100mm VESA mounting kit (PV01) - Operation System
This system comes without operating system. It is compatible with
- Windows 10 (64 bit)
- Windows 8 / 8.1 (64 bit)
- Windows 7 (64 bit) [2]
- Linux (64 Bit) [3] - Processor
Intel Celeron J1900, Quad Core
CPU clock frequency: 2.00 GHz, max. Turbo frequency: 2.42 GHz
Silvermont architecture, Bay Trail-D platform, 22nm structure
CPU cores/Threads: 4/4
Cache: 2 MB
Thermal Design Power (TDP): 10W
SOC design with integrated graphics processor - Integrated Graphics
The Graphics Processing Unit (GPU) is integrated into the processor
Intel HD Graphics (7th gen), graphics frequency: 688~854 MHz
Supports DirectX 11.0, OpenGL 4.0, OpenCL 1.2, HDCP 1.3 (Blu-ray)
Execution Units (EU): 4
Three video outputs:
- HDMI: max. 1920x1200 resolution @ 60Hz
- Display Port: max. 2560x1600 resolution @ 60Hz
- D-Sub (VGA): max. 1920x1200 resolution @ 60Hz
Dual display: supports max. two independent displays
Full hardware acceleration:
- for decode: H.264, MPEG2, MVC, VC-1, VP8, MJPEG
- for encode: H.264, MPEG2, MVC - UEFI Firmware
8Mbit Flash ROM with AMI's Aptio UEFI BIOS Firmware
Based on the Unified Extensible Firmware Interface (UEFI) [1]
Supports Power fail resume / AC power on state / always on / always off
Supports Wake-on-LAN (WOL) from S3, S3, S5 ACPI states
Supports boot up from external flash memory cards - Memory
1x SO-DIMM slot with 204 pins
Supports one module DDR3L-1333 (PC3-10600) at 1.35V
Maximum capacity: 8 GB
DDR3L-1600 is supported at DDR3L-1333 clock rate
Caution: This mainboard does only support 1.35V DDR3L memory modules.
Note: DDR3L has a lower operation voltage compared to DDR3 - Optical drive (optional)
Supports an optical DVD or Blu-ray slim-line drive
Serial ATA interface, 12.7 mm height, Slimline SATA connector - Hard disk drive/SSD (2.5")
Supports one Serial ATA hard disk (5400 / 7200 rpm)
or one SATA SSD drive in 6.35cm/2.5" format
Serial ATA II Interface with up to 300 MB/s transfer speed
Supports a drive with max. 9.5 mm height
Supports Unified Extensible Firmware Interface (UEFI) - Integrated Audio
Realtek ALC269 Audio Codec with Azalia and D3 mode support
Two analog audio connectors (3.5mm):
1) Line out (head phone)
2) Microphone input - Card Reader
Integrated card reader supports SD, SDHC and SDXC memory flash cards - Wired Network
RJ45 connector supports Gigabit LAN at 10/100/1000 Mbit/sec.
Network controller Realtek RTL8411
Supports Wake-on-LAN (WOL) from S3, S3, S5 ACPI states
Supports network boot by Preboot eXecution Environment (PXE) - Wireless Network (WLAN)
Half-size Mini PCIe card with RTL8188EE chip
Supports IEEE 802.11b/g/n, max. 150Mbps up-/downstream
Security: WPA/WPA2(-PSK), WEP 64/128bit, IEEE 802.11x/i - Front Panel Connectors
1x USB 2.0
SD card reader - Back Panel Connectors
HDMI digital video and audio output
DisplayPort digital video and audio output
D-Sub/ VGA analog video output (15 pin)
1x USB 3.0
3x USB 2.0
Gigabit network (LAN, RJ45)
Audio Line-out (head phone)
Microphone input
DC input for the external power adapter
Perforation for TV antenna (diameter: 9 mm) - Internal USB Connectors
Internal USB 2.0 Type-A connector for USB dongle
(for e.g. memory stick, 3G stick, DVB-T stick, etc.)
Supports boot from internal USB memory stick. - LEDs and Buttons
Power button
Power LED (blue) - Power Supply
External 40W AC/DC power adapter (fanless), 19V / 2.1A
AC Input: 100~240V AC, 50~60Hz
Automatic voltage adjust
Dimensions: 89.5 x 37 x 26.5 mm (LWH)
DC Connector: 5.5/2.5mm (outer/inner diameter) - Optional Accessories
- VESA mount made of metal (PV01)
- Adapter for second 2.5" drive instead of optical drive (PHD2N) - 24/7 nonstop operation
This device is approved for 24/7 permanent operation.
Requirements:
- Free circulation of air amongst the PC must be guaranteed.
- Ventilation holes must be clear.
- Any installed hard disk must also be approved for permanent
operation by its manufacturer (max. one hard disk) - Environmental Spec
Operating temperature range: 0~35°C
Relative humidity range: 10~90% (non-condensing) - Zertifikate und Konformität
EMI: FCC, CE, BSMI, C-Tick
Sicherheit: CB, BSMI, ETL
Weitere: RoHS, Energy Star, ErP
Dieses Gerät wird als informationstechnische Einrichtung (ITE) der Klasse B eingestuft und ist hauptsächlich für den Betrieb im Wohn- und Bürobereich vorgesehen. Durch das CE-Zeichen wird die Konformität mit den folgenden EU-Richtlinien bestätigt:
(1) Richtlinie 2004/108/EG über die elektromagnetische Verträglichkeit (EMC),
(2) Richtlinie 2006/95/EG über die Sicherheit von elektrischen Betriebsmitteln (LVD),
(3) Richtlinie 2009/125/EG über die umweltgerechte Gestaltung energieverbrauchsrelevanter Produkte (ErP) und
(4) Richtlinie 1999/5/EG über Funkanlagen und Telekommunikationseinrichtungen (R&TTE) festgelegt sind.
[1] UEFI-Firmware (versus BIOS)
Just as many modern PCs, the XS35V4 does away completely with a BIOS, but uses a pure *) UEFI firmware instead. The terms UEFI firmware and BIOS are widely used synonymously, but hardware initialising is now performed by the UEFI. Users might not even notice, but the operating system must be installed and executed in UEFI mode. UEFI creates a GUID Partition Table (GPT) on the system partition instead of a Master Boot Record (MBR). A PC running UEFI firmware alone but have a 64-bit operating system installed.
*) Notice: In transition period from BIOS to UEFI mainboard manufacturers still used to employ a traditional BIOS for compatibility reasons. Thanks to the integrated "Compatibility Support Module" (CSM), older Windows versions could boot from mainboards with a UEFI firmware.
[2] Windows 7 64-bit is supported since BIOS version XS35V400.110. If a BIOS update is required, the built-in UEFI shell must be used. Please refer to the FAQ section on the Shuttle website for more information on this matter. Prior to the installation of Windows 7, BIOS must be entered and "Windows 7" must be selected as the operating system under "Boot", "OS-Selection".
[3] Linux 64-bit: A number of Linux distributions with updated Kernel versions have already been tested successfully (date: June 2014). Please refer to the FAQ section on the Shuttle website for more information on this matter.
