• Chassis
    Barebone PC with a black plastic chassis
    Dimensions: 142 x 142 x 42 mm (LWH) = 847 ml
    Weight: 0.4 kg net, 1.2 kg gross
    Hole for Kensington Lock
    Includes vertical stand and 75 / 100 mm VESA mount
  • Low Power Consumption
    Power consumption in idle mode under Windows 10: ca. 5 W
  • Operation Position
    1) Horizontal
    2) Vertical with stand
    3) VESA-mounted behind an appropriate monitor
  • Operation System
    This barebone system comes without operating system.
    It is compatible with:
    - Windows 10, 64-bit
    - Linux, 64-bit
  • Processor
    Model: Intel Core i3-7100U (ULV)
    System-on-a-chip architecture (SoC): no chipset required
    BGA1356 package - directly soldered onto the mainboard
    Code name: Kaby Lake-U (7th Generation Intel Core)
    Cores / Threads: 2 / 4
    Clock rate: 2.4 GHz
    L1/L2/L3 Cache: 128 kB / 512 kB / 3072 kB
    Memory controller: DDR4-2133 Dual Channel (1.2 V)
    TDP wattage: 15 W maximum
    Manufacturing process: 14 nm
    Maximum Tjunction Temperature: 100 °C
    Supports Hyper-Threading (HT), 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2
    Integrated graphics engine
  • Cooling Fan
    Built-in CPU cooling fan with 4-pin connector
    Supports temperature-controlled RPM fan speed
  • Integrated Graphics
    Intel HD graphics 620
    GPU clock frequency: 300~1000 MHz
    Execution Units (EUs): 24
    Two digital audio/video ports support two independent screens (dual monitoring):
    Supports Ultra HD / 4K resolution at 3840 x 2160 Pixels
    1) DisplayPort 1.2 [1] supports Ultra HD @ 60 Hz
    2) HDMI 1.4b supports Ultra HD @ 30 Hz
  • Mainboard / BIOS
    AMI BIOS in 8 MByte EEPROM with SPI interface
    Supports resume after power failure
    Supports Wake on LAN (WOL)
    Supports Power on by RTC Alarm
    Supports booting from USB devices and SD card reader
    Supports hardware monitoring and watch dog function
    Supports Unified Extensible Firmware Interface (UEFI)
    Supports Firmware TPM v2.0 (fTPM)
  • Power Adapter
    External 65 W power adapter (fanless)
    Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
    Output: 19 V DC, max. 3.42 A, max. 65 W
    DC Connector: 5.5 / 2.5 mm (outer/inner diameter)
  • Memory support
    2x SO-DIMM slots with 260 pins
    Supports DDR4-2133 (PC4-17000) SDRAM at 1.2 V
    Supports Dual Channel mode
    Supports a maximum of 16 GB per DIMM, maximum total size: 32 GB
    Supports two unbuffered DIMM modules (no ECC or registered)
  • 2.5" Drive Bay
    Supports one Serial ATA hard disk
    or one SATA SSD drive in 6.35 cm / 2.5" format
    Device height: 15 mm (max.)
    Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
  • Card Reader
    Integrated SD card reader
    Supports SD, SDHC and SDXC memory flash cards
    Supports booting from SD card
  • M.2 Slot for SSDs
    The M.2 2280 BM slot provides the following interfaces:
    - PCI-Express Gen. 3.0 X4 with up to 4 GB/s Data Transfer Speed
    - SATA v3.0 (max. 6 Gbps)
    It supports M.2 cards with a width of 22 mm
    and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
    Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe SSDs (with M key)
  • Audio
    Audio Realtek® ALC 662 High-Definition Audio Codec
    3.5 mm / 4-pole combo audio connector for headphones and microphone [2]
    Digital multi-channel audio output: via HDMI and DisplayPort
  • Gigabit LAN
    Ethernet Controller Intel i211
    Supports 10 / 100 / 1.000 MBit/s operation (Gigabit)
    Supports WAKE ON LAN (WOL)
    Supports network boot by Preboot eXecution Environment (PXE)
    IEEE 802.3az Energy Efficient Ethernet (EEE)
    Interface: PCIe v2.1
  • Wireless LAN
    Built-in M.2-2230-A/E WLAN card and internal antenna
    Single-Chip 1T1R WLAN Controller Realtek RTL8188EE
    Supports IEEE 802.11b/g/n, max. 150 Mbps up-/downstream
    Security: WPA/WPA2(-PSK), WEP 64/128 bit, IEEE 802.11x/i
  • Front Panel connectors
    USB 3.0 type A
    USB 3.0 type C
    SD card reader (supports SD, SDHC, SDXC)
    Power button
    Power LED (blue, flashing when in suspend mode)
    HDD LED (orange)
  • Back Panel connectors
    DisplayPort 1.2 [1]
    HDMI 1.4b
    2x USB 2.0
    Gigabit LAN (RJ45)
    Audio Combo Port for headphones and microphone (3.5 mm jack, 4-pole) [2]
    DC-input connector for external power adapter
    2x perforation for optional external WLAN antennas
  • Left Side connectors
    Serial RS232 COM port (D-Sub, 9-pin)
    Note: The serial connector (COM port) cannot be used if the NC03U3 is operated in vertical position.
  • Always-On Jumper
    By removing Jumper JP1 (please refer to the Quick Installation Guide)
    the system will start unconditionally once power is applied. [4]
  • Clear CMOS Jumper
    Short Jumper JP2 for about 10 seconds to restore factory settings of BIOS.
  • Supplied Accessories
    Multi-language Quick Installation Guide
    Driver DVD for Windows
    VESA mount set (two parts, made of steel, with 6 screws)
    2x aluminium stand with screws for vertical operation
    Bracket for a 2.5" drive with 8 screws
    Power adapter with AC power cord
  • Optional Accessories
    WLN-M: Wireless LAN module with two external antennas, 
    supports WiFi IEEE 802.11n/ac (2.4 / 5 GHz) and Bluetooth 4.0
  • Environmental Spec
    Operating temperature range: 0~40 °C [3]
    Relative humidity range: 10~90% (non-condensing)
  • Conformity/Certifications
    EMI: CE, FCC, BSMI, RCM, R&TTE, VCCI
    Safety: CB, BSMI, ETL
    Other: RoHS, Energy Star, ErP
    This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
    (1) 2004/108/EC relating to electromagnetic compatibility (EMC),
    (2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
    (3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
    (4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)

[1] How to convert DisplayPort into HDMI/DVI
The DisplayPort outputs can be converted to HDMI or DVI by an additional, passive adapter cable. For example:
DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)
DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)
The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either DisplayPort (without an adapter) or HDMI/DVI (with an adapter).
However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter. In this case an active adapter like Delock 62496 is required.
Connecting a UHD/4K display via the present HDMI port means the refreshing rate is limited to 24 Hz. 60 Hz can only be achieved by using the DisplayPort port. Should your display have a HDMI 2.0 connector, a refreshing rate of 60 Hz can be achieved by using an active adapter such as the Club 3D CAC-1070 for example.
[2] Audio connector
The 3.5 mm audio jack at the back panel of this device supports both a 4-pole connector for headphones and microphone and headphones with only a 3-pole connector. Headsets with separate connectors for headphones and microphone, though, require an appropriate adapter, if also the microphone should be used.
[3] Caution: For high ambient temperatures over 35 °C we strongly recommend to use SSDs (supporting at least 70 °C) instead of hard disks.
[4] Power-on after Power Fail:
The BIOS setup provides a "Power-on after Power Fail" function that can be found under "Power Management Configuration". This function determines the PC's behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why this PC also comes with a hardware-based solution. By removing Jumper JP1 (please refer to the Quick Installation Guide), the system will start unconditionally once power is applied.

© 2020 Shuttle Europe | Infos légales | Contact | CGV | Protection des données | Plan du site