• Fanless and silent
    Passive cooling, no fan noise at all
    Perfect to be used in noise-sensitive environments
    Fanless, dust-free and thus virtually maintenance-free
  • Low power consumption
    Power consumption: idle: 10-11W, full load: 22-30W (without/with graphics)
    (measured with 2x 2GB SO-DIMM, 500 GB 2.5" hard disk)
  • 24/7 nonstop operation
    This device is approved for 24/7 permanent operation.
    Requirements:
    - Free circulation of air amongst the PC must be guaranteed.
    - Ventilation holes must stay clear.
    - If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
  • Chassis
    Slim-PC (Nettop) with black chassis made of steel
    Without cooling fan, passive cooling only
    The bays for memory, 2.5" drives and Mini-PCIe cards
    can be easily accessed by removing two cover plates.
    Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
    Weight: 1.43 kg net and 2.13 kg gross
    Two holes for Kensington Lock and numerous 
    threaded holes (M3) at both sides of the chassis
  • Operation Position:
    1) Device must only be used in vertical position with the DVI port facing up
    2) Please make sure to use either the supplied feet or the VESA mount
  • Operation System
    This barebone system comes without operating system.
    It is compatible with Windows 8, Windows 7, Windows XP and Linux
    Supports 32 and 64 bit.
  • Processor
    Model: Intel Celeron 1037U (ULV)
    Code name: Ivy Bridge (3rd Gen. Core)
    Cores / Threads: 2 / 2
    Clock rate: 1.8 GHz
    L1/L2/L3 cache: 128 kB / 512 kB / 2048 kB
    Memory controller: DDR3-1333/1600 Dual Channel
    TDP wattage: 17 W maximum
    Manufacturing process: 22 nm
    Socket: FCBGA1023
    Enhanced SpeedStep technology
    Maximum Tjunction Temperature: 105°C
    Integrated Intel HD graphics engine
    Supports 64 Bit, VT-x with EPT, Enhanced SpeedStep, NX bit, SSE4
  • Integrated graphics
    Intel HD graphics
    Clock rate: 350~1000 MHz
    Maximum resolution: 1920x1200 (analog or digital)
    Execution Units (EU): 6
    Supports two independent screens
    Supports DirectX 11.1, OpenGL 4.0
    Supports full AVC/VC1/MPEG2 hardware decoding
    HDMI supports HD video plus multi-channel digital audio via a single cable
  • Mainboard / Chipset / BIOS
    Shuttle Mainboard FS47
    All capacitors are high quality solid capacitors
    Chipset: Intel® NM70 Express
    Supports resume after power failure [6]
    Supports Wake on LAN (WOL)
    Supports Power on by RTC Alarm
    Supports boot from USB devices and SD card reader
    AMI BIOS in 8 MByte EEPROM with SPI interface
    Supports hardware monitoring and watch dog functionality
    Supports Unified Extensible Firmware Interface (UEFI) [1]
  • Power Adapter
    External 65 W power adapter (fanless)
    Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
    Output: 19 V DC, max. 3.42 A, max. 65 W
    DC Connector: 5.5/2.5mm (outer/inner diameter)
  • Memory support
    2x SO-DIMM slots with 204 pins
    Supports DDR3-1333 (PC3-10600) and DDR3-1600 (PC3-12800) SDRAM
    Supports Dual Channel mode
    Supports max. 8 GB per DIMM,  maximum total size of 16 GB
    Supports two unbuffered DIMM modules (no ECC)
  • Mini PCIe Slots
    Two Mini PCI Express expansion slots: full size and half size
    1) the half size slot is occupied with a WLAN module
    2) the full size slot supports PCIe 2.0, SATA 3G and USB 2.0
    and can either be used for a Mini-PCIe card or
    for a Mini SATA (mSATA) flash memory card [3]
    Please use the "Mini-PCIE / mSATA Select" function in the BIOS setup.
  • Audio
    Audio Realtek® ALC 662 High-Definition Audio (5.1 channel)
    Two analog audio connectors (3.5mm) at the back panel: 
    1) 2 channel line out (head phone)
    2) microphone input
    Digital multi-channel audio output: via HDMI
  • Dual Gigabit LAN Controller
    Dual Realtek 8111G Ethernet network controller (Gigabit)
    Supports 10 / 100 / 1.000 MBit/s operation
    With two RJ45 ports (dual network) supports Teaming [2]
    Supports WAKE ON LAN (WOL)
    Supports network boot by Preboot eXecution Environment (PXE)
  • Wireless Network (WLAN)
    Built-in Mini-PCIe WLAN card (half size) and internal antenna
    Single-Chip 1T1R WLAN Controller Realtek RTL8188CE
    Supports IEEE 802.11b/g/n, max. 150Mbps up-/downstream
    Security: WPA/WPA2(-PSK), WEP 64/128bit, IEEE 802.11x/i
  • 2.5" drive bay
    Supports one Serial ATA hard disk
    or one SATA SSD drive in 6.35cm/2.5" format
    Device height: 9.5 or 12.5 mm (max.)
    Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
    Supports Unified Extensible Firmware Interface (UEFI) [1]
    Note: no Serial ATA cable is required
  • Card Reader
    Integrated SD card reader 
    Supports SD, SDHC and SDXC memory flash cards
    Supports boot up from SD card
  • Front Panel connectors
    4x USB 2.0
    2x RS232 serial ports (5V/12V, 1x switchable to RS422 / RS485)
    with black plastic caps
    SD card reader (supports SD, SDHC, SDXC)
    Power button
    Power LED (blue)
    HDD LED (yellow)
  • Back Panel connectors
    HDMI 1.3 connector (supports DVI-D with optional adapter)
    DVI-I connector (supports VGA with optional adapter)
    2x USB 3.0
    2x Gigabit LAN (RJ45)
    Microphone input
    Audio Line-out (headphone)
    DC-input connector for external power adapter
    4 pin connector (2.54 mm pitch) for power button, Clear CMOS and 5V DC [4]
    Perforation for optional Wireless LAN antennas (2 holes)
  • Other onboard connectors
    Jumper J1: Power on after power fail (hardware solution) [8]
    Connector for CMOS battery (with battery)
    Fan connector (4 pins) not occupied
  • Scope of delivery
    Multi-language user guide
    Two metal feet
    VESA mount for 75/100mm standard (two metal brackets)
    Four thumbscrews M3 x 5 mm (screws together VESA mount and PC)
    Four screws M4 x 10 mm (to fix the VESA mount to the external device)
    Three screws M3 x 4 mm and a rack (to mount a 2.5" storage into the bay)
    Driver DVD (Windows 8 / 7 / XP)
    External power adapter with power cord
  • Environmental Specifications
    Operating temperature range: 0~40 °C [5]
    Relative humidity, non-condensing: 10~90%
  • Conformity/Certifications
    EMI: FCC, CE, BSMI, C-Tick
    Safety: CB, BSMI, ETL, CCC
    This device is classed as a technical information
    equipment (ITE) in class B and is intended for use in 
    living room and office. The CE-mark approves the 
    conformity by the EU-guidelines:
    - EMV-guideline 89/336/EWG electromagnetic tolerance
    - LVD-guideline 73/23/EWG use of electric devices 
    within certain voltage-limits

[1] Unified Extensible Firmware Interface (UEFI) - required when booting from hard disks larger than 2.2 TB
[2] Teaming Mode
The teaming function allows you to group both available network adapters together to function as a single adapter - a method of creating a virtual LAN. The benefit of this approach is that it enables load balancing and failover.
[3] mini-SATA (mSATA)
not to be confused with the "micro SATA" connector, is a newer industry standard which converts the electrical SATA interface (1.5 or 3.0 Gbit/s) to the pysical "Mini PCI Express" mini card form factor.
[4] Four pin header at the back panel
This header allows for connecting an external power button.
It also provides 5V DC voltage for external devices and the Clear CMOS function.
[5] Caution: for high ambient temperature over 35°C we strongly recommend to use SSDs (supporting at least 70°C) and rugged SODIMM memory with wide temperature range (up to 95°C).
Suggested vendors for rugged memory modules:
Samsung: http://www.samsung.com/... 
Elpida: http://www.elpida.com/... 
Micron: http://www.micron.com/...
[6] Power on after power fail:
The BIOS setup provides a "Power-On after Power Fail" function that can be found under "Power Management Configuration". As the name indicates, this function determines the PC's behaviour after power failure: (1) unconditional power on, (2) restore former status or (3) keep system turned off. As a matter of the nature of this function, it may fail after short power failures. This is why the DS437 also comes with a hardware-based solution. By removing Jumper J1 (pls. refer quick user guide) the system will start unconditionally once power is supplied.

© 2020 Shuttle Europe | Infos légales | Contact | CGV | Protection des données | Plan du site